DN, IC, HG, KD, MJ, and Co; X-ray measurement/characterization campaign 
|
The machine was warmed up remotemy
The FPC is ready. The laser is locked.
9h Start HV |
|
KD; shift du 19 décembre 2025
|
7h20: mise en chauffe en remote (frigo/chiller, laser, modulateur, cyclage)
*** Programme *** |
|
MJ; shift twiss Q1 versus soleno
|
Modulateur en chauffe
Alarme rendant impossible clim casemate . Maher envoie un mail a urgencevc
Check Sf6 : 2 bar ==> Appel JN ==> ajout sf6 2.5 bar |
|
KD; shift du 06 janvier 2026
|
8h: mise en chauffe en remote (cyclage, modulateur, frigo/chillers, laser)
problème lancement cyclage RI-C1: QP.04, QP.09 et QP.10
Sole 238 |
|
VM DN MJ KD; shift du 07 janvier 2026 16x
|
7h55: mise en chauffe en remote (modulateur, frigo/chillers, laser, cyclage)
11h25 HV is ON
Archivage lance |
|
IC, HG, RC, DN, JM; Test of the new receipt from BMAD Isol = 242 A 13x
|
8h55: mise en chauffe (modulateur, frigo/chillers, laser, cyclage)
10h20 HV ON
Start with the receipt nominal. problem with the RF gun laser camera. Solved. |
|
KD, IC, VM, RC; shift du 9 janvier 2026 6x
|
8h05: mise en chauffe en remote (modulateur, frigo/chillers, laser, cyclage)
09h06 HV is ON
10h10 receipt recipe_recipe_LI_TL_RI_all_20260108_17_34_30.txt (242 A BMAD). RF gun phase 226 dg. Sect Att. 2.457 dB, sect. phase 214 dg. |
|
KD; shift du 13 janvier 2026
|
7h55 : mise en chauffe en remote (chiller/frigo, laser, modulateur, cyclage)
9h : démarrage, pas de soucis au niveau du trig
16h30 : demarrage anneau pour recette 230A |
|
VM, RC, MJ, IC; Test Soleno=245, optic issue de la simu Julien Matching
|
08h36 Warm-up ThomX: Modulator, Laser, Fridge
8h41 Chillers were started, cycling all magnets.
09h40 HV is ON |
|
IC; Ring studies
|
08h56 Warm-up ThomX: Modulator, Laser, Fridge
Chillers were started, cycling all magnets.
Low SF6 pressure. |
|
IC, VM, ND;
|
08h29 Warm-up ThomX: Modulator, Laser, Fridge
Chillers were started, cycling all magnets.
10h48 Beam is in the ring after resolving a lot of problems. The receipt loaded: recipe_recipe_LI_TL_RI_all_20260115_18_10_34.txt, with Linac-Tl |
|
VM, ND, VC;
|
08h35 Warm-up ThomX: Modulator, Laser, Fridge
08h41 Chillers were started, cycling all magnets.
09h40 HV is ON |
|
KD MJ RC DN; Position Horiz FPC ("spectres dromadaires")
|
7h55: mise en chauffe en remote (modulateur, cyclage, laser, frigo/chillers)
==> plus de trig sur la machine (sur toute la plage de scan de la phase stab du laser PC). ==> OK, je suis une truffe le laser était
"off" |
|
IC, VM; Beam studies
|
7h45: mise en chauffe en remote (modulateur, laser, frigo/chillers)
08h41 HV is on
08h49 RF gun phase 152 dg., sect phase 208 dg. beam is in the ring W/O RF |
|
IC, VM; Ring studies
|
7h45: mise en chauffe en remote (modulateur, cyclage, laser, frigo/chillers)
08h43 HV is on
RF gun phase (laser phase) for maximum charge is out of the range, close to 360 dg. or 10 dg. Help is needed! |
|
KD, HG, VM; Laser PC status
|
** l'iris a été changée et est opérationnelle
/!\ problème dans l'offset il faut ajouter 0.5mm à la valeur relu par Tango (pour 1.3mm
il faut mettre 0.8 mm dans l'ATK panel) |
|
Entered by Super Team from 127.0.0.1 on Fri Feb 6 08:26:22 2026;
|
08h25 Warm-up ThomX: Modulator, Laser, Fridge
08h33 Chillers were started, cycling all magnets.
09h31 HV is on. Vacuum: Li/Vac1 4e-9, Li/Vac2 3e-9, Li/Vac3 3e-9, Li/Vac4 1e-9 |
|
VM && HG; Linac commissioning
|
09h12 Warm-up ThomX: Modulator, Laser, Fridge
09h21 Chillers were started, cycling all magnets.
RF 50 pps |
|
Entered by Super Team from 127.0.0.1 on Fri Feb 13 17:38:00 2026; SHift du jour
|
The code for laser alignment does not work properly --> done by hand
H 5.244
V 4.654 |
|
MJ, KD,VM,IC, RC, DN; shift du 17 fevrier 2026 10x
|
7h50 : mise en chauffe en remote (frigo/chillers, modulateur, laser, cyclage)
Le cyclage de RI-C1/QP.08, RI-C1/QP.11 et RI-C2/QP.03 ne démarre pas tout seul (action nécessaire sur le boutton cyclage de l'élément).
Programme - Etude "IP dromadaire" ==> Scan pos horizontale FPC + phase |