Clean Airflow Dust measurements, posted by Manar Amer at Optical room about detectors and electronics | utilities 
|
Dust measurement done today on top of the SBox average 10min
Manar
Amer wrote:
The dust meter cap was cleaned using Alcohol, and using the filter white |
|
Spincoater - Mirrror cleaning , posted by Manar Amer at Optical room about lasers and optics | utilities
|
Used the spincoater and pure water to clean dielectric mirrors which will be installed inside the SBox for directing the reflection line.
The method : place pure alchole on mirror - wipe it using white sterile tissue (in one direction) - clean with pure water in spincoater suing
cotton swap . |
KBox Alignment , posted by Manar Amer at Optical room about lasers and optics 7x
|
Starting with the alignment of the KBox using CW Koheras.
The size of the CW output from the collimator at 1 meter from is ~ 2.4 mm, to be adjusted with lenses to match the cavity !!! (attached
image) |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics 6x
|
SBox alignment, using CW laser Koheras power 1 mW
Finished M1 and M2 alignment using the diffraction patterns seen on the beam profiler,
the beam fit is not very good ?? (image taken)
Positions of Ma1 and Ma2 motors are |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
After pointers and Advice from Aurélien,
improvement of the beam alignment through M1 and M2 irises was done.
To improve the image on the beam profiler, I cleaned the alignment mirrors and the windows using pure ethanol and optical lens cleaning tissue, |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Remember to update the position of the reference Irises tomorrow !!!!
Manar
Amer wrote:
After pointers and Advice from Aurélien, |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics 9x
|
Adjust the placement of the Irises (done at the start of the day, adjusted at the end
when M1 mirror was placed)
Improvement on the
Ma1 and Ma2 (The Alignment Mirrors)
Improves the alignment a bit. There is an observation where there |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Finished the alignment of the SBox with M1 of SBox placed, to be changed to gamma factory mirror later
Observed what seems to be transmission through M2 mirror, to be confirmed. image attached shows it
a PowerPoint attached showing the details of today's work. |
|
Spincoater - Mirrror cleaning , posted by Manar Amer at Optical room about lasers and optics | utilities
|
Images of the SBox mirrors cleaned at the same time when the cavity was aligned.
Directly from the spincoater to the SBox directly.
PowerPoint attached shows details |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Last week In FP cavity we had all SBox mirrors including the damaged M1 mirror.
The beating was observed with just a slight adjustment on M4 alignment.
In addition, it was also observed while driving the piezo of the CW laser. |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Today; replaced the M1 SBox mirror with M1 from gamma factory , following the previous alignment.
Removed all mirrors and cleaned them one by one.
Started with no M1, placed M2 did its alignment through M3 pinhole, then placed M3 aligned it through M4 pinhole, then placed M4 aligned it through |
|
Spincoater - Mirrror cleaning , posted by Manar Amer at Optical room about lasers and optics | utilities
|
PowerPoint shows the detailed images of all the mirrors before and after cleaning.
Images of SBox mirrors and M1 from Gamma factory attached only for the front after cleaning
the lines showing are on the back of the mirrors, they come from the spinning mount the mirrors are fixed on in the spin-coater. |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Yesterday, to find the source of why the mode is deformed, I tried to rotate the mirrors to see if there is a change.
I started with M2 and rotated it by ~ 90 degrees, there is a change in the shape of the beam.(image attached)
Will see if changing M2 to the spare M2 from SBox can fix the issue. |
|
Spincoater - Mirrror cleaning , posted by Manar Amer at Optical room about lasers and optics | utilities
|
Following the observation that when rotating M2 plan mirror of SBox the deformation position of the mode changes.
M2 was replaced with M2 spare of SBox
images of the mirror front side attached before and after cleaning, no spots at the center, but there seems to be 2 spots far from the center |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
M2 Sbox changed to spare. Alignment of M2 was redone.
With the help of Ronic , We observe fundamental mode of the cavity with higher order modes. A frequency scan on the piezo was done to find the
beating frequency , the shape is elliptical with no clear deformation. |
|
Spincoater - Mirrror cleaning , posted by Manar Amer at Optical room about lasers and optics | utilities
|
While repeating the alignment, the mirrors were cleaned using the spin-coater and placed again.
The current mirrors placed in the SBox are
M1 plane injection from Gamma factory |
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics 7x
|
The external and internal alignment was redone.
External Alignment : the collimator position moved so in order to have a good start I placed 2 metallic mirrors and did a rough retrace of it's
line through the cavity box. |
|
Fundamental Mode TEM00, posted by Manar Amer at Optical room about lasers and optics
|
The current setup for the SBox has a beam viewer and 2 photodiodes placed at reflection and transmission.
The CW laser piezoelectric crystal was driven using the lase lock system to observe the 00 mode.
Mode Observed and has no reflection (from what was previously seen) |
|
Fundamental Mode TEM00, posted by Manar Amer at Optical room about lasers and optics
|
Adding images from the transmission after the spherical mirrors M3 and M4 window for a resonating mode inside the cavity.
There appears to be some misalignment from the center of the mirror ???
|
|
SBox Alignment , posted by Manar Amer at Optical room about lasers and optics
|
Closing Series for Alignment.
Beating observed, beam is in the locking stages
|